Systemair SR160.H.SYS.G4+F7.EC LPF.S1.R1
Модель: SR160.H.SYS.G4+F7.EC
Артикул: 372522
Features
The new SysAer have been designed and optimized to operate with R410A refrigerant fluid.
Energy class A, Ecodesign 2021 ready - applicable from 2021
High SEER and SCOP
They are available in cooling only and reversible versions.
The range consists in 10 sizes (SR55, SR65, SR80 ,SR95, SR105, SR120, SR140, SR160, SR190 and SR210) and covers a nominal cooling capacity range from 49 to 216 kW and a nominal heating capacity range from 49 to 211 kW
2 circuits for the entire range to optimize performances at part load, and avoid cold draught during defrost mode. The range SysAer is provided with 2 compressors from sizes SR55 to SR140, and 4 compressors from sizes SR190 to SR210.
These configurations which allow up to 4 capacity stages give an immediate return on investment.
The general operation status of the machine is continuously under the control of an IATC controller
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel. All galvanized steel components are individually painted by a special painting process before the assembly of the unit.
The units SysAer are equipped with double skin panels as a standard to prevent insulation fiber entering into the building and harmful build-up of bacteria or contaminants. It also ensure better thermal insulation.
Great accessibility to internal components for service operations.
Removable drain pan.
Aeraulic configuration
The SysAer is provided with blast and return fans, PLUG FAN type with an AC motor or with an EC motor, Low Pressure or High Pressure according to the configuration selected by the customer
Economiser with 2 dampers
The factory-mounted economiser with 2 dampers is available with the R1, R2 and R4 configurations.
The control program for the economiser is optimized to use the biggest possible amount of outdoor air, in order to save consumption of the compressors, and thus energy.
Energy recovery systems
RECO : energy recovery on the exhaust air
The factory-mounted economiser with 3 dampers, is equipped with an EC plug fan return fan as a standard and is available with the R1 and R2 configurations.
The economiser increases the partial load operation of the compressors and improves the seasonal efficiency thanks to a proportional-action control function.
The economiser with 3 combined dampers, with proportional modulation of the outdoor-recycled-extracted air allows an extraction up to 100% of the total air flow (in equivalent quantity to the intake of outdoor air).
It provides real energy savings by regulating the air renewal.
TRECO : thermodynamic energy recovery between Fresh air and Exhaust air
This option is available only on the SysAer equipped with 3 dampers (not compatible with the FRECO system).
This thermodynamic system for recovering energy between the exhaust air and fresh air is delivered entirely mounted and factory tested. It is composed of an independent refrigeration circuit and a dedicated control.
This energy recovery system allows real energy savings
FRECO : food refrigeration heat recovery
The SysAER provided with a FRECO system uses the heat generated by the condensers of the refrigeration systems of a supermarket as a free source of heat.
Heating
• The SysAER can be equipped, according to the specifications of the customers, with an additional heating system. This equipment is installed and tested in the factory.• Hot water coil
• Electric heating
• Gas burner
Control
A factory-programmed direct digital control (the IATC) handles and optimizes the operation all throughout the year, emphasizing comfort and the saving of energy.
The IATC regulates the heating and the cooling according to the desired ambient temperature, controlling the cyclical operation and the rotation of the compressors, as well as the de-icing, overload protection, high and low pressures, compliance with the requirements for minimum ventilation and the fan mode, continuous or intermittent.
Compensation for the summer-winter ambient temperature and a min/max ambient temperature setting are provided as standard.
A system for building management provided by another supplier can communicate via ModBus with a card of the RS-485 type as an option, on the user interface. The parameters of the SysAER are then transmitted and can be modified from a remote monitoring and troubleshooting station.
In case several SysAER are installed (in zones or groups whether or not different), it is possible to display the parameters of each unit with only one interface for the entire installation. The principle consists in connecting all of the units in parallel, using a single pLAN bus (proprietary protocol), while connecting the graphics interface to a master controller. This IATC will centralize certain operating modes, such as the "occupied/unoccupied" mode.
Systemair SR190.H.SYS.G4+F7.EC LPF.S1.R1
Модель: SR190.H.SYS.G4+F7.EC
Артикул: 372523
Features
The new SysAer have been designed and optimized to operate with R410A refrigerant fluid.
Energy class A, Ecodesign 2021 ready - applicable from 2021
High SEER and SCOP
They are available in cooling only and reversible versions.
The range consists in 10 sizes (SR55, SR65, SR80 ,SR95, SR105, SR120, SR140, SR160, SR190 and SR210) and covers a nominal cooling capacity range from 49 to 216 kW and a nominal heating capacity range from 49 to 211 kW
2 circuits for the entire range to optimize performances at part load, and avoid cold draught during defrost mode. The range SysAer is provided with 2 compressors from sizes SR55 to SR140, and 4 compressors from sizes SR190 to SR210.
These configurations which allow up to 4 capacity stages give an immediate return on investment.
The general operation status of the machine is continuously under the control of an IATC controller
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel. All galvanized steel components are individually painted by a special painting process before the assembly of the unit.
The units SysAer are equipped with double skin panels as a standard to prevent insulation fiber entering into the building and harmful build-up of bacteria or contaminants. It also ensure better thermal insulation.
Great accessibility to internal components for service operations.
Removable drain pan.
Aeraulic configuration
The SysAer is provided with blast and return fans, PLUG FAN type with an AC motor or with an EC motor, Low Pressure or High Pressure according to the configuration selected by the customer
Economiser with 2 dampers
The factory-mounted economiser with 2 dampers is available with the R1, R2 and R4 configurations.
The control program for the economiser is optimized to use the biggest possible amount of outdoor air, in order to save consumption of the compressors, and thus energy.
Energy recovery systems
RECO : energy recovery on the exhaust air
The factory-mounted economiser with 3 dampers, is equipped with an EC plug fan return fan as a standard and is available with the R1 and R2 configurations.
The economiser increases the partial load operation of the compressors and improves the seasonal efficiency thanks to a proportional-action control function.
The economiser with 3 combined dampers, with proportional modulation of the outdoor-recycled-extracted air allows an extraction up to 100% of the total air flow (in equivalent quantity to the intake of outdoor air).
It provides real energy savings by regulating the air renewal.
TRECO : thermodynamic energy recovery between Fresh air and Exhaust air
This option is available only on the SysAer equipped with 3 dampers (not compatible with the FRECO system).
This thermodynamic system for recovering energy between the exhaust air and fresh air is delivered entirely mounted and factory tested. It is composed of an independent refrigeration circuit and a dedicated control.
This energy recovery system allows real energy savings
FRECO : food refrigeration heat recovery
The SysAER provided with a FRECO system uses the heat generated by the condensers of the refrigeration systems of a supermarket as a free source of heat.
Heating
• The SysAER can be equipped, according to the specifications of the customers, with an additional heating system. This equipment is installed and tested in the factory.• Hot water coil
• Electric heating
• Gas burner
Control
A factory-programmed direct digital control (the IATC) handles and optimizes the operation all throughout the year, emphasizing comfort and the saving of energy.
The IATC regulates the heating and the cooling according to the desired ambient temperature, controlling the cyclical operation and the rotation of the compressors, as well as the de-icing, overload protection, high and low pressures, compliance with the requirements for minimum ventilation and the fan mode, continuous or intermittent.
Compensation for the summer-winter ambient temperature and a min/max ambient temperature setting are provided as standard.
A system for building management provided by another supplier can communicate via ModBus with a card of the RS-485 type as an option, on the user interface. The parameters of the SysAER are then transmitted and can be modified from a remote monitoring and troubleshooting station.
In case several SysAER are installed (in zones or groups whether or not different), it is possible to display the parameters of each unit with only one interface for the entire installation. The principle consists in connecting all of the units in parallel, using a single pLAN bus (proprietary protocol), while connecting the graphics interface to a master controller. This IATC will centralize certain operating modes, such as the "occupied/unoccupied" mode.
Systemair SR210.H.SYS.G4+F7.EC LPF.S1.R1
Модель: SR210.H.SYS.G4+F7.EC
Артикул: 372524
Features
The new SysAer have been designed and optimized to operate with R410A refrigerant fluid.
Energy class A, Ecodesign 2021 ready - applicable from 2021
High SEER and SCOP
They are available in cooling only and reversible versions.
The range consists in 10 sizes (SR55, SR65, SR80 ,SR95, SR105, SR120, SR140, SR160, SR190 and SR210) and covers a nominal cooling capacity range from 49 to 216 kW and a nominal heating capacity range from 49 to 211 kW
2 circuits for the entire range to optimize performances at part load, and avoid cold draught during defrost mode. The range SysAer is provided with 2 compressors from sizes SR55 to SR140, and 4 compressors from sizes SR190 to SR210.
These configurations which allow up to 4 capacity stages give an immediate return on investment.
The general operation status of the machine is continuously under the control of an IATC controller
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel. All galvanized steel components are individually painted by a special painting process before the assembly of the unit.
The units SysAer are equipped with double skin panels as a standard to prevent insulation fiber entering into the building and harmful build-up of bacteria or contaminants. It also ensure better thermal insulation.
Great accessibility to internal components for service operations.
Removable drain pan.
Aeraulic configuration
The SysAer is provided with blast and return fans, PLUG FAN type with an AC motor or with an EC motor, Low Pressure or High Pressure according to the configuration selected by the customer
Economiser with 2 dampers
The factory-mounted economiser with 2 dampers is available with the R1, R2 and R4 configurations.
The control program for the economiser is optimized to use the biggest possible amount of outdoor air, in order to save consumption of the compressors, and thus energy.
Energy recovery systems
RECO : energy recovery on the exhaust air
The factory-mounted economiser with 3 dampers, is equipped with an EC plug fan return fan as a standard and is available with the R1 and R2 configurations.
The economiser increases the partial load operation of the compressors and improves the seasonal efficiency thanks to a proportional-action control function.
The economiser with 3 combined dampers, with proportional modulation of the outdoor-recycled-extracted air allows an extraction up to 100% of the total air flow (in equivalent quantity to the intake of outdoor air).
It provides real energy savings by regulating the air renewal.
TRECO : thermodynamic energy recovery between Fresh air and Exhaust air
This option is available only on the SysAer equipped with 3 dampers (not compatible with the FRECO system).
This thermodynamic system for recovering energy between the exhaust air and fresh air is delivered entirely mounted and factory tested. It is composed of an independent refrigeration circuit and a dedicated control.
This energy recovery system allows real energy savings
FRECO : food refrigeration heat recovery
The SysAER provided with a FRECO system uses the heat generated by the condensers of the refrigeration systems of a supermarket as a free source of heat.
Heating
• The SysAER can be equipped, according to the specifications of the customers, with an additional heating system. This equipment is installed and tested in the factory.• Hot water coil
• Electric heating
• Gas burner
Control
A factory-programmed direct digital control (the IATC) handles and optimizes the operation all throughout the year, emphasizing comfort and the saving of energy.
The IATC regulates the heating and the cooling according to the desired ambient temperature, controlling the cyclical operation and the rotation of the compressors, as well as the de-icing, overload protection, high and low pressures, compliance with the requirements for minimum ventilation and the fan mode, continuous or intermittent.
Compensation for the summer-winter ambient temperature and a min/max ambient temperature setting are provided as standard.
A system for building management provided by another supplier can communicate via ModBus with a card of the RS-485 type as an option, on the user interface. The parameters of the SysAER are then transmitted and can be modified from a remote monitoring and troubleshooting station.
In case several SysAER are installed (in zones or groups whether or not different), it is possible to display the parameters of each unit with only one interface for the entire installation. The principle consists in connecting all of the units in parallel, using a single pLAN bus (proprietary protocol), while connecting the graphics interface to a master controller. This IATC will centralize certain operating modes, such as the "occupied/unoccupied" mode.
Systemair SR55.H.SYS.G4+F7.EC LPF.S1.R1D
Модель: SR55.H.SYS.G4+F7.EC
Артикул: 372515
Features
The new SysAer have been designed and optimized to operate with R410A refrigerant fluid.
- Energy class A, Ecodesign 2021 ready - applicable from 2021
- High SEER and SCOP
- They are available in cooling only and reversible versions.
- The range consists in 10 sizes (SR55, SR65, SR80 ,SR95, SR105, SR120, SR140, SR160, SR190 and SR210) and covers a nominal cooling capacity range from 49 to 216 kW and a nominal heating capacity range from 49 to 211 kW.
- 2 circuits for the entire range to optimize performances at part load, and avoid cold draught during defrost mode. The range SysAer is provided with 2 compressors from sizes SR55 to SR140, and 4 compressors from sizes SR190 to SR210.
- These configurations which allow up to 4 capacity stages give an immediate return on investment.
- The general operation status of the machine is continuously under the control of an IATC controller
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel. All galvanized steel components are individually painted by a special painting process before the assembly of the unit.
The units SysAer are equipped with double skin panels as a standard to prevent insulation fiber entering into the building and harmful build-up of bacteria or contaminants. It also ensure better thermal insulation.
Great accessibility to internal components for service operations.
Removable drain pan.
Aeraulic configuration
The SysAer is provided with blast and return fans, PLUG FAN type with an AC motor or with an EC motor, Low Pressure or High Pressure according to the configuration selected by the customer.
Economiser with 2 dampers
The factory-mounted economiser with 2 dampers is available with the R1, R2 and R4 configurations.
The control program for the economiser is optimized to use the biggest possible amount of outdoor air, in order to save consumption of the compressors, and thus energy.
Energy recovery systems:
• RECO : energy recovery on the exhaust air
The factory-mounted economiser with 3 dampers, is equipped with an EC plug fan return fan as a standard and is available with the R1 and R2 configurations.
The economiser increases the partial load operation of the compressors and improves the seasonal efficiency thanks to a proportional-action control function.
The economiser with 3 combined dampers, with proportional modulation of the outdoor-recycled-extracted air allows an extraction up to 100% of the total air flow (in equivalent quantity to the intake of outdoor air).
It provides real energy savings by regulating the air renewal.
• TRECO : thermodynamic energy recovery between Fresh air and Exhaust air
This option is available only on the SysAer equipped with 3 dampers (not compatible with the FRECO system).
This thermodynamic system for recovering energy between the exhaust air and fresh air is delivered entirely mounted and factory tested. It is composed of an independent refrigeration circuit and a dedicated control.
This energy recovery system allows real energy savings
• FRECO : food refrigeration heat recovery
The SysAER provided with a FRECO system uses the heat generated by the condensers of the refrigeration systems of a supermarket as a free source of heat.
Heating
• The SysAER can be equipped, according to the specifications of the customers, with an additional heating system. This equipment is installed and tested in the factory.• Hot water coil
• Electric heating
• Gas burner
Control
A factory-programmed direct digital control (the IATC) handles and optimizes the operation all throughout the year, emphasizing comfort and the saving of energy.
The IATC regulates the heating and the cooling according to the desired ambient temperature, controlling the cyclical operation and the rotation of the compressors, as well as the de-icing, overload protection, high and low pressures, compliance with the requirements for minimum ventilation and the fan mode, continuous or intermittent.
Compensation for the summer-winter ambient temperature and a min/max ambient temperature setting are provided as standard.
A system for building management provided by another supplier can communicate via ModBus with a card of the RS-485 type as an option, on the user interface. The parameters of the SysAER are then transmitted and can be modified from a remote monitoring and troubleshooting station.
In case several SysAER are installed (in zones or groups whether or not different), it is possible to display the parameters of each unit with only one interface for the entire installation. The principle consists in connecting all of the units in parallel, using a single pLAN bus (proprietary protocol), while connecting the graphics interface to a master controller. This IATC will centralize certain operating modes, such as the "occupied/unoccupied" mode.
Systemair SR65.H.SYS.G4+F7.EC HPF.S1.R1D
Модель: SR65.H.SYS.G4+F7.EC
Артикул: 372516
Features
The new SysAer have been designed and optimized to operate with R410A refrigerant fluid.
- Energy class A, Ecodesign 2021 ready - applicable from 2021
- High SEER and SCOP
- They are available in cooling only and reversible versions.
- The range consists in 10 sizes (SR55, SR65, SR80 ,SR95, SR105, SR120, SR140, SR160, SR190 and SR210) and covers a nominal cooling capacity range from 49 to 216 kW and a nominal heating capacity range from 49 to 211 kW.
- 2 circuits for the entire range to optimize performances at part load, and avoid cold draught during defrost mode. The range SysAer is provided with 2 compressors from sizes SR55 to SR140, and 4 compressors from sizes SR190 to SR210.
- These configurations which allow up to 4 capacity stages give an immediate return on investment.
- The general operation status of the machine is continuously under the control of an IATC controller
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel. All galvanized steel components are individually painted by a special painting process before the assembly of the unit.
The units SysAer are equipped with double skin panels as a standard to prevent insulation fiber entering into the building and harmful build-up of bacteria or contaminants. It also ensure better thermal insulation.
Great accessibility to internal components for service operations.
Removable drain pan.
Aeraulic configuration
The SysAer is provided with blast and return fans, PLUG FAN type with an AC motor or with an EC motor, Low Pressure or High Pressure according to the configuration selected by the customer.
Economiser with 2 dampers
The factory-mounted economiser with 2 dampers is available with the R1, R2 and R4 configurations.
The control program for the economiser is optimized to use the biggest possible amount of outdoor air, in order to save consumption of the compressors, and thus energy.
Energy recovery systems:
• RECO : energy recovery on the exhaust air
The factory-mounted economiser with 3 dampers, is equipped with an EC plug fan return fan as a standard and is available with the R1 and R2 configurations.
The economiser increases the partial load operation of the compressors and improves the seasonal efficiency thanks to a proportional-action control function.
The economiser with 3 combined dampers, with proportional modulation of the outdoor-recycled-extracted air allows an extraction up to 100% of the total air flow (in equivalent quantity to the intake of outdoor air).
It provides real energy savings by regulating the air renewal.
• TRECO : thermodynamic energy recovery between Fresh air and Exhaust air
This option is available only on the SysAer equipped with 3 dampers (not compatible with the FRECO system).
This thermodynamic system for recovering energy between the exhaust air and fresh air is delivered entirely mounted and factory tested. It is composed of an independent refrigeration circuit and a dedicated control.
This energy recovery system allows real energy savings
• FRECO : food refrigeration heat recovery
The SysAER provided with a FRECO system uses the heat generated by the condensers of the refrigeration systems of a supermarket as a free source of heat.
Heating
• The SysAER can be equipped, according to the specifications of the customers, with an additional heating system. This equipment is installed and tested in the factory.• Hot water coil
• Electric heating
• Gas burner
Control
A factory-programmed direct digital control (the IATC) handles and optimizes the operation all throughout the year, emphasizing comfort and the saving of energy.
The IATC regulates the heating and the cooling according to the desired ambient temperature, controlling the cyclical operation and the rotation of the compressors, as well as the de-icing, overload protection, high and low pressures, compliance with the requirements for minimum ventilation and the fan mode, continuous or intermittent.
Compensation for the summer-winter ambient temperature and a min/max ambient temperature setting are provided as standard.
A system for building management provided by another supplier can communicate via ModBus with a card of the RS-485 type as an option, on the user interface. The parameters of the SysAER are then transmitted and can be modified from a remote monitoring and troubleshooting station.
In case several SysAER are installed (in zones or groups whether or not different), it is possible to display the parameters of each unit with only one interface for the entire installation. The principle consists in connecting all of the units in parallel, using a single pLAN bus (proprietary protocol), while connecting the graphics interface to a master controller. This IATC will centralize certain operating modes, such as the "occupied/unoccupied" mode.
Systemair SR80.H.SYS.G4+F7.EC LPF.S1.R1D
Модель: SR80.H.SYS.G4+F7.EC
Артикул: 372517
Features
The new SysAer have been designed and optimized to operate with R410A refrigerant fluid.
- Energy class A, Ecodesign 2021 ready - applicable from 2021
- High SEER and SCOP
- They are available in cooling only and reversible versions.
- The range consists in 10 sizes (SR55, SR65, SR80 ,SR95, SR105, SR120, SR140, SR160, SR190 and SR210) and covers a nominal cooling capacity range from 49 to 216 kW and a nominal heating capacity range from 49 to 211 kW.
- 2 circuits for the entire range to optimize performances at part load, and avoid cold draught during defrost mode. The range SysAer is provided with 2 compressors from sizes SR55 to SR140, and 4 compressors from sizes SR190 to SR210.
- These configurations which allow up to 4 capacity stages give an immediate return on investment.
- The general operation status of the machine is continuously under the control of an IATC controller
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel. All galvanized steel components are individually painted by a special painting process before the assembly of the unit.
The units SysAer are equipped with double skin panels as a standard to prevent insulation fiber entering into the building and harmful build-up of bacteria or contaminants. It also ensure better thermal insulation.
Great accessibility to internal components for service operations.
Removable drain pan.
Aeraulic configuration
The SysAer is provided with blast and return fans, PLUG FAN type with an AC motor or with an EC motor, Low Pressure or High Pressure according to the configuration selected by the customer.
Economiser with 2 dampers
The factory-mounted economiser with 2 dampers is available with the R1, R2 and R4 configurations.
The control program for the economiser is optimized to use the biggest possible amount of outdoor air, in order to save consumption of the compressors, and thus energy.
Energy recovery systems:
• RECO : energy recovery on the exhaust air
The factory-mounted economiser with 3 dampers, is equipped with an EC plug fan return fan as a standard and is available with the R1 and R2 configurations.
The economiser increases the partial load operation of the compressors and improves the seasonal efficiency thanks to a proportional-action control function.
The economiser with 3 combined dampers, with proportional modulation of the outdoor-recycled-extracted air allows an extraction up to 100% of the total air flow (in equivalent quantity to the intake of outdoor air).
It provides real energy savings by regulating the air renewal.
• TRECO : thermodynamic energy recovery between Fresh air and Exhaust air
This option is available only on the SysAer equipped with 3 dampers (not compatible with the FRECO system).
This thermodynamic system for recovering energy between the exhaust air and fresh air is delivered entirely mounted and factory tested. It is composed of an independent refrigeration circuit and a dedicated control.
This energy recovery system allows real energy savings
• FRECO : food refrigeration heat recovery
The SysAER provided with a FRECO system uses the heat generated by the condensers of the refrigeration systems of a supermarket as a free source of heat.
Heating
• The SysAER can be equipped, according to the specifications of the customers, with an additional heating system. This equipment is installed and tested in the factory.• Hot water coil
• Electric heating
• Gas burner
Control
A factory-programmed direct digital control (the IATC) handles and optimizes the operation all throughout the year, emphasizing comfort and the saving of energy.
The IATC regulates the heating and the cooling according to the desired ambient temperature, controlling the cyclical operation and the rotation of the compressors, as well as the de-icing, overload protection, high and low pressures, compliance with the requirements for minimum ventilation and the fan mode, continuous or intermittent.
Compensation for the summer-winter ambient temperature and a min/max ambient temperature setting are provided as standard.
A system for building management provided by another supplier can communicate via ModBus with a card of the RS-485 type as an option, on the user interface. The parameters of the SysAER are then transmitted and can be modified from a remote monitoring and troubleshooting station.
In case several SysAER are installed (in zones or groups whether or not different), it is possible to display the parameters of each unit with only one interface for the entire installation. The principle consists in connecting all of the units in parallel, using a single pLAN bus (proprietary protocol), while connecting the graphics interface to a master controller. This IATC will centralize certain operating modes, such as the "occupied/unoccupied" mode.
Systemair SR95.H.SYS.G4+F7.EC LPF.S1.R1D
Модель: SR95.H.SYS.G4+F7.EC
Артикул: 372518
Features
The new SysAer have been designed and optimized to operate with R410A refrigerant fluid.
- Energy class A, Ecodesign 2021 ready - applicable from 2021
- High SEER and SCOP
- They are available in cooling only and reversible versions.
- The range consists in 10 sizes (SR55, SR65, SR80 ,SR95, SR105, SR120, SR140, SR160, SR190 and SR210) and covers a nominal cooling capacity range from 49 to 216 kW and a nominal heating capacity range from 49 to 211 kW.
- 2 circuits for the entire range to optimize performances at part load, and avoid cold draught during defrost mode. The range SysAer is provided with 2 compressors from sizes SR55 to SR140, and 4 compressors from sizes SR190 to SR210.
- These configurations which allow up to 4 capacity stages give an immediate return on investment.
- The general operation status of the machine is continuously under the control of an IATC controller
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel. All galvanized steel components are individually painted by a special painting process before the assembly of the unit.
The units SysAer are equipped with double skin panels as a standard to prevent insulation fiber entering into the building and harmful build-up of bacteria or contaminants. It also ensure better thermal insulation.
Great accessibility to internal components for service operations.
Removable drain pan.
Aeraulic configuration
The SysAer is provided with blast and return fans, PLUG FAN type with an AC motor or with an EC motor, Low Pressure or High Pressure according to the configuration selected by the customer.
Economiser with 2 dampers
The factory-mounted economiser with 2 dampers is available with the R1, R2 and R4 configurations.
The control program for the economiser is optimized to use the biggest possible amount of outdoor air, in order to save consumption of the compressors, and thus energy.
Energy recovery systems:
• RECO : energy recovery on the exhaust air
The factory-mounted economiser with 3 dampers, is equipped with an EC plug fan return fan as a standard and is available with the R1 and R2 configurations.
The economiser increases the partial load operation of the compressors and improves the seasonal efficiency thanks to a proportional-action control function.
The economiser with 3 combined dampers, with proportional modulation of the outdoor-recycled-extracted air allows an extraction up to 100% of the total air flow (in equivalent quantity to the intake of outdoor air).
It provides real energy savings by regulating the air renewal.
• TRECO : thermodynamic energy recovery between Fresh air and Exhaust air
This option is available only on the SysAer equipped with 3 dampers (not compatible with the FRECO system).
This thermodynamic system for recovering energy between the exhaust air and fresh air is delivered entirely mounted and factory tested. It is composed of an independent refrigeration circuit and a dedicated control.
This energy recovery system allows real energy savings
• FRECO : food refrigeration heat recovery
The SysAER provided with a FRECO system uses the heat generated by the condensers of the refrigeration systems of a supermarket as a free source of heat.
Heating
• The SysAER can be equipped, according to the specifications of the customers, with an additional heating system. This equipment is installed and tested in the factory.• Hot water coil
• Electric heating
• Gas burner
Control
A factory-programmed direct digital control (the IATC) handles and optimizes the operation all throughout the year, emphasizing comfort and the saving of energy.
The IATC regulates the heating and the cooling according to the desired ambient temperature, controlling the cyclical operation and the rotation of the compressors, as well as the de-icing, overload protection, high and low pressures, compliance with the requirements for minimum ventilation and the fan mode, continuous or intermittent.
Compensation for the summer-winter ambient temperature and a min/max ambient temperature setting are provided as standard.
A system for building management provided by another supplier can communicate via ModBus with a card of the RS-485 type as an option, on the user interface. The parameters of the SysAER are then transmitted and can be modified from a remote monitoring and troubleshooting station.
In case several SysAER are installed (in zones or groups whether or not different), it is possible to display the parameters of each unit with only one interface for the entire installation. The principle consists in connecting all of the units in parallel, using a single pLAN bus (proprietary protocol), while connecting the graphics interface to a master controller. This IATC will centralize certain operating modes, such as the "occupied/unoccupied" mode.
Systemair STDT 16E Motor Protection
Модель: STDT
Артикул: 5153
Пристрій теплового захисту електродвигуна
Пристрої STDT 16E (монтується на рейці) та STDT 16 (для настінного монтажу) автоматично відключають подачу живлення при розмиканні теплових контактів, вбудованих в обмотки електродвигуна. Пристрій теплового захисту підключається до джерела живлення (400 В) та термоконтакт електродвигуна.
При спрацьовуванні захисту перезапуск електродвигуна здійснюється натисканням чорної кнопки після остигання електродвигуна. Пристрій теплового захисту електродвигуна можна використовувати разом із трансформатором. Можливе ручне увімкнення та відключення живлення на вентилятор.
Контакт аварійної сигналізації (К) поставляється на окреме замовлення. Контакт аварійної сигналізації є вбудованим контактом, що подає сигнал при розмиканні термоконтактів.
Systemair SYSAQUA105.H.1P-SP.WPS.AVM
Модель: SYSAQUA105.H.1P-SP.WPS.AVM
Артикул: 372049
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA125.H.1P-SP.WPS.AVM
Модель: SYSAQUA125.H.1P-SP.WPS.AVM
Артикул: 372051
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA140.H.1P-SP.WPS.AVM
Модель: SYSAQUA140.H.1P-SP.WPS.AVM
Артикул: 370190
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA140.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA140.H.1P-SP.WPS.AVM.T
Артикул: 370191
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA150.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA150.H.1P-SP.WPS.AVM.T
Артикул: 370193
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA190.H.1P-SP.WPS.AVM
Модель: SYSAQUA190.H.1P-SP.WPS.AVM
Артикул: 370196
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA190.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA190.H.1P-SP.WPS.AVM.T
Артикул: 370197
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.