Systemair STDT 16E Motor Protection
Модель: STDT
Артикул: 5153
Пристрій теплового захисту електродвигуна
Пристрої STDT 16E (монтується на рейці) та STDT 16 (для настінного монтажу) автоматично відключають подачу живлення при розмиканні теплових контактів, вбудованих в обмотки електродвигуна. Пристрій теплового захисту підключається до джерела живлення (400 В) та термоконтакт електродвигуна.
При спрацьовуванні захисту перезапуск електродвигуна здійснюється натисканням чорної кнопки після остигання електродвигуна. Пристрій теплового захисту електродвигуна можна використовувати разом із трансформатором. Можливе ручне увімкнення та відключення живлення на вентилятор.
Контакт аварійної сигналізації (К) поставляється на окреме замовлення. Контакт аварійної сигналізації є вбудованим контактом, що подає сигнал при розмиканні термоконтактів.
Systemair SYSAQUA105.H.1P-SP.WPS.AVM
Модель: SYSAQUA105.H.1P-SP.WPS.AVM
Артикул: 372049
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA125.H.1P-SP.WPS.AVM
Модель: SYSAQUA125.H.1P-SP.WPS.AVM
Артикул: 372051
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA140.H.1P-SP.WPS.AVM
Модель: SYSAQUA140.H.1P-SP.WPS.AVM
Артикул: 370190
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA140.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA140.H.1P-SP.WPS.AVM.T
Артикул: 370191
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA150.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA150.H.1P-SP.WPS.AVM.T
Артикул: 370193
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA190.H.1P-SP.WPS.AVM
Модель: SYSAQUA190.H.1P-SP.WPS.AVM
Артикул: 370196
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA190.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA190.H.1P-SP.WPS.AVM.T
Артикул: 370197
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA210.H.1P-SP.WPS.AVM
Модель: SYSAQUA210.H.1P-SP.WPS.AVM
Артикул: 370198
SysAquaL/SysAquaH 140 to 210 have been designed and optimized to operate with R410A refrigerant fluid.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 5 sizes (140, 150, 170, 190 and 210) and covers a nominal cooling capacity range from 127 to 208 kW and a nominal heating capacity range from 140 to 213kW
All units are equipped with four scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller
The SysAquaL and SysAquaH units can operate without water tank, thanks to the IHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions.
The minimum water volume requested in cooling mode is 3.5 litres of buffer volume per kW.
In heating mode, 6.5 litres of buffer volume per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energy savings).
A fans peed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
Systemair SYSAQUA35.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA35.H.1P-SP.WPS.AVM.T
Артикул: 372036
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA40.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA40.H.1P-SP.WPS.AVM.T
Артикул: 372038
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA45.H.1P-SP.WPS.AVM
Модель: SYSAQUA45.H.1P-SP.WPS.AVM
Артикул: 372039
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA45.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA45.H.1P-SP.WPS.AVM.T
Артикул: 372040
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA55.H.1P-SP.WPS.AVM
Модель: SYSAQUA55.H.1P-SP.WPS.AVM
Артикул: 372041
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.
Systemair SYSAQUA75.H.1P-SP.WPS.AVM.T
Модель: SYSAQUA75.H.1P-SP.WPS.AVM.T
Артикул: 372046
SysAquaL/SysAquaH 25 to 125 have been designed and optimized to operate with R410A refrigerant fluid. They are of single refrigerant circuit type.
They are available in cooling only (SysAquaL) and heat pump (SysAquaH) versions.
Each versions consists of 11 sizes (25, 30, 35, 40, 45, 55, 65, 75, 90, 105 & 125) and covers a nominal cooling capacity range from 25.0 to 122 kW and a nominal heating capacity range from 26.9 to 120 kW.
All units are equipped with two scroll compressors fitted in tandem for adapting to partial system loads.
The general operation status of the machine is continuously under the control of an IHM controller.
The SysAquaL and SysAquaH units can operate without water tank, thanks to the lHM controller that implements an auto- adaptative control logic ensuring a total protection of the compressors at different load or water volume conditions. The minimum water volume requested in cooling mode is 3.5 litres per kW for application air conditioning and 10 litres per kW for application process.
In heating mode, 12.5 litres per kW are recommended in order to guarantee homogeneous temperatures during the defrosting cycles (comfort and energysavings). A fan speed controller can be also supplied as factory-fitted option to authorize the unit to operate in cooling mode at low ambient temperature.
SysAquaL and SysAquaH units can be supplied in several versions:
- STD (Standard) version : lncludes a low noise (LS) acoustical performance.
- XLN (Extra low noise) version : Obtained by the installation of acoustic box around compressors.
- HPF version : lncreases the static pressure.
Cabinet and structure
The cabinet and structure of the unit are of heavy duty galvanized steel.All galvanized steel components are individually painted by a special painting process before the assembly of the unit. This painting system performs a homogeneous protection to the corrosion.The painting is a polyester powder based type, coloured in RAL 7040.
The units SysAquaL/SysAquaH are suitable for outdoor installation, directly on the building roof or at the ground level.
Compressors
Each unit is equipped with two scroll compressors fitted on a rail and assembled together to form tandem compressors.
The compressors are then mounted on rubber pads in order to eliminate noise and vibration transmissions. The compressor motor shave a direct startup. Each motor is cooled by the refrigerant gas and is equipped with an overload protection.
A phase sequence monitor is supplied as standard.
Evaporator
The evaporator is consisting of a stainless steel plate heat exchanger insulated with closed cell synthetic foam. lt is protected by an antifreeze electric heater to ensure a good protection against freezing at low ambient temperature (-10 °C min.) when the unit is switchedoff.
Maximum working pressure is 10 bar at water side and 45 at refrigerant side.